New Hub Two delivered but i need to know how to set into modem mode only
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Plusnet Community
- :
- Forum
- :
- Help with my Plusnet services
- :
- My Router
- :
- Re: New Hub Two delivered but i need to know how t...
- « Previous
-
- 1
- 2
- Next »
Re: New Hub Two delivered but i need to know how to set into modem mode only
Wednesday
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
- CPU: Intel Celeron N3450 at 1.10 GHz (Quad-core).
- RAM: 8 GB (8380 MB).
Its a Zimaboard so hopefully but might be pushed but i have a couple of Rasberry Pi's i could offload some tasks to
Re: New Hub Two delivered but i need to know how to set into modem mode only
Wednesday
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
This https://forum.opnsense.org/index.php?topic=36926.0 would suggest that spec may struggle ...
Might be ok if you don't use any QoS ?
Superusers are not staff, but they do have a direct line of communication into the business in order to raise issues, concerns and feedback from the community.
Re: New Hub Two delivered but i need to know how to set into modem mode only
Wednesday
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
If i was going to update to a new router any recommendations?
Re: New Hub Two delivered but i need to know how to set into modem mode only
Wednesday
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
Depends on your requirements above and beyond basic routing ?
I use a Tplink ER605 flashed with Openwrt. The Ubiquity ER-X is similar and easier to flash. . Both are based around the mt7621 chip set , which with hardware offloading enabled will handle my 900Mb connection. They are pretty basic hardware , gigabit wan and 4 LAN ports. However with h/w offload disabled ( to allow QoS ) they will max out at around 500Mb
Ideally for a 900Mb connection you need something with at least a 1.6ghz quad core processor to run one of the generic router softwares i.e Openwrt, Opnsense , PFsense
Superusers are not staff, but they do have a direct line of communication into the business in order to raise issues, concerns and feedback from the community.
Re: New Hub Two delivered but i need to know how to set into modem mode only
Wednesday
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
Attached is my basic home Network i will see how it behaves.
I think the router would be the only weak point
https://xbackbone.osopolar.cloud/ZubU1/BaMAYiFU20.png
Re: New Hub Two delivered but i need to know how to set into modem mode only
yesterday
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
That's a lot of kit for a home network, I can see why you want a 900Mb connection😁
TBH I'd be inclined to give your existing router a try and see how it performs. If it can't cope , then use the Hub 2 (with wifi disabled?) either on a temporary basis whilst you research a better router, or permanently. The hub 2 will certainly handle the 900Mb throughput.
In my case I use the ER605 with Openwrt (instead of the Hub 2) primarily due to its ability to host a direct VPN connection to my office. It also has a USB port to which I can connect my phone as a 5g backup in case of FTTP failure.
Both the ER605 and the ER-X (no USB) I mentioned can be picked up for around £50. If you wanted to future proof with something that could better handle more throughput then the TPlink ER707 https://www.tp-link.com/uk/business-networking/vpn-router/er707-m2/ might be worth a look BUT its around £200!
Superusers are not staff, but they do have a direct line of communication into the business in order to raise issues, concerns and feedback from the community.
- « Previous
-
- 1
- 2
- Next »
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Plusnet Community
- :
- Forum
- :
- Help with my Plusnet services
- :
- My Router
- :
- Re: New Hub Two delivered but i need to know how t...