cancel
Showing results for 
Search instead for 
Did you mean: 

New Hub Two delivered but i need to know how to set into modem mode only

OsoPolar
Grafter
Posts: 27
Thanks: 1
Registered: ‎17-01-2023

Re: New Hub Two delivered but i need to know how to set into modem mode only

 

  • CPU: Intel Celeron N3450 at 1.10 GHz (Quad-core).
  • RAM: 8 GB (8380 MB).

Its a Zimaboard so hopefully but might be pushed but i have a couple of Rasberry Pi's i could offload some tasks to   

 

MisterW
Superuser
Superuser
Posts: 16,189
Thanks: 6,172
Fixes: 445
Registered: ‎30-07-2007

Re: New Hub Two delivered but i need to know how to set into modem mode only

This https://forum.opnsense.org/index.php?topic=36926.0 would suggest that spec may struggle ...

Might be ok if you don't use any QoS ?

Superusers are not staff, but they do have a direct line of communication into the business in order to raise issues, concerns and feedback from the community.

OsoPolar
Grafter
Posts: 27
Thanks: 1
Registered: ‎17-01-2023

Re: New Hub Two delivered but i need to know how to set into modem mode only

If i was going to update to a new router  any recommendations?

MisterW
Superuser
Superuser
Posts: 16,189
Thanks: 6,172
Fixes: 445
Registered: ‎30-07-2007

Re: New Hub Two delivered but i need to know how to set into modem mode only

Depends on your requirements above and beyond basic routing ?

I use a Tplink ER605 flashed with Openwrt. The Ubiquity ER-X is similar and easier to flash. . Both are based around the mt7621 chip set , which with hardware offloading enabled will handle my 900Mb connection. They are pretty basic hardware , gigabit wan and 4 LAN ports. However with h/w offload disabled ( to allow QoS ) they will max out at around 500Mb

Ideally for a 900Mb connection you need something with at least a 1.6ghz quad core processor to run one of the generic router softwares i.e Openwrt, Opnsense , PFsense

Superusers are not staff, but they do have a direct line of communication into the business in order to raise issues, concerns and feedback from the community.

OsoPolar
Grafter
Posts: 27
Thanks: 1
Registered: ‎17-01-2023

Re: New Hub Two delivered but i need to know how to set into modem mode only

Attached is my basic home Network i will see how it behaves.
I think the router would be the only weak point 

https://xbackbone.osopolar.cloud/ZubU1/BaMAYiFU20.png

MisterW
Superuser
Superuser
Posts: 16,189
Thanks: 6,172
Fixes: 445
Registered: ‎30-07-2007

Re: New Hub Two delivered but i need to know how to set into modem mode only

That's a lot of kit for a home network, I can see why you want a 900Mb connection😁

TBH I'd be inclined to give your existing router a try and see how it performs. If it can't cope , then use the Hub 2 (with wifi disabled?) either on a temporary basis whilst you research a better router, or permanently. The hub 2 will certainly handle the 900Mb throughput.

In my case I use the ER605 with Openwrt (instead of the Hub 2) primarily due to its ability to host a direct VPN connection to my office. It also has a USB port to which I can connect my phone as a 5g backup in case of FTTP failure.

Both the ER605 and the ER-X (no USB) I mentioned can be picked up for around £50. If you wanted to future proof with something that could better handle more throughput then the TPlink ER707 https://www.tp-link.com/uk/business-networking/vpn-router/er707-m2/ might be worth a look BUT its around £200!

Superusers are not staff, but they do have a direct line of communication into the business in order to raise issues, concerns and feedback from the community.